M&S Systems MC602 Instrukcja Użytkownika Pobierz pdf

CONGRATULATIONS!

Your purchase of an M&S music and communications system is an investment that will provide years of enjoyment and service for

your customer.

M&S audio products are backed with more than 40 years of experience in the design and manufacture of precision acoustical

equipment for the home. To ensure that your customer receives the high-quality music and voice reproduction that the system

is designed to deliver, it is important that each step of the installation be done carefully. If you follow the step-by-step illustrated

instructions below, the result will be a successful professional-quality installation. In the event you need troubleshooting assistance,

please call our technical staff at 1-800-366-9422.

K USE ONLY M&S SYSTEMS BRAND CABLE as

called out in these instructions. The cable is designed and

constructed with electrical specifications necessary for

proper audio performance. I

MPORTANT: THE USE OF NON

M&S SYSTEMS' BRAND CABLE OR CABLE SUBSTITUTION

WILL VOID PRODUCT WARRANTY. Note: All M&S Systems'

cable has M&S Systems and the part number printed on it!

K DO NOT power up master until all remote stations and

speakers are connected.

K DO ensure that all rough-in instructions (literature number

115750) have been followed before power is applied to

system.

K DO NOT SPLICE CABLES. Splices are unreliable and

defeat the signal isolation properties of the cable.

K DO NOT COIL OR BUNDLE the MS4X cable. This will

cause electronic feedback.

K If extra cables have been run for possible future speaker

additions, care must be taken that these cables do not get

connected to the master unit. Unterminated cables (no

station) connected to the master unit may cause

electronic feedback that will damage the master unit.

K DO NOT overtighten the screws for the remote stations

or the master as the plastic face panels may crack or strip

out.

Figure 1

Figure 2 Figure 3

Figure 4

Tools required: Phillips screwdriver #2, Standard flat screwdriver

#1, wire stripper/cutter.

The finish-out installation should be made after the application of

wall covering material.

REMOTE STATIONS N65 SERIES

At each remote station location,

strip approximately 4 Inches of

jacket (MS4XSC) from wire and

separate the colored conductors

from one another. Strip 1/2 Inch

of insulation from each conductor

as shown in figure 1. Cut each

shield drain

wire at the shield

foil to prevent

them from

touching each

other (MS4XSC

only). Connect

each colored

conductor to its

respective

screw terminal

as shown in

figure 2. Mount each remote station to it's mounting ring using the

two screws provided with each station as shown in figure 3.

SATELLITE CONTROL STATIONS

NRC65 SERIES

At each satellite control

station location, strip

approximately 4 Inches of

jacket (MS4XSC and

MS2SXSC) from wires and

separate colored

conductors from one

another. Strip 1/2 Inch of

insulation from each

conductor. Cut off the

drain wire from the

Black/White pair. Connect

the remaining drain wires

together from both cables

Figure 5

Figure 6

Figure 7

Figure 8

Figure 9

Figure 10

using a wire nut (MS4XSC only). Terminate each colored

conductor to its respective screw terminal as shown in figure 4.

Connect the Blue and Violet wires to the terminals on the

satellite speaker(s). Mount the satellite control station to

mounting ring or housing using the two screws provided with the

station.

SATELLITE VOLUME

CONTROL

MVC1 SERIES

At each satellite control station

location, strip approximately 4

Inches of jacket (MS4XSC and

MS2SXSC) from wires and

separate colored conductors

from one another. Strip 1/2 Inch

of insulation from each

conductor. Connect drain wires together from both cables using

a wire nut (MS4XSC only). Wire nut each colored conductor to

its respective wire as shown in figure 5. Connect Blue and Violet

wires to the corresponding terminals of the satellite speaker(s).

Mount the volume control to the single gang box using the two

screws provided with the volume control.

PATIO REMOTE

STATIONS

NW65 SERIES

At each remote

station location, strip

approximately 4

Inches of jacket

(MS4XSC) from wire

and separate colored

conductors from one

another. Strip 1/2

Inch of insulation

from each conductor. Cut each shield drain wire at the shield foil

to prevent them from touching each other (MS4XSC only).

Connect each colored conductor together using wire nuts as

shown in figure 6. Mount the patio station to housing using the

two screws provided with the station.

S ATELLITE

CONTROL

STATIONS

NWRC65

SERIES

At each satellite control

station location, strip

approximately 4 Inches

of jacket (MS4XSC and

MS2SXSC) from wires

and separate colored conductors from one another. Strip 1/2 Inch

of insulation from each conductor. Connect drain wires together

from both cables using a wire nut (MS4XSC only). Connect each

colored conductor together using wire nuts as shown in figure 7.

Terminate Blue and Violet wires to the corresponding terminals

of the satellite speaker(s). Mount satellite control station to

mounting ring or housing using the two screws provided with the

station.

E XTERNAL

MUSIC SOURCE

AWPM

Connect the cables

from the gang box to

the 'Y' cables shipped

with the AWPM wall

plate as shown in

figure 8. Use the labels

provided to mark the

plate as identified on

the respective cables. Connect the 'Y' cables to the plate as shown

and mount the plate using the two screws provided.

DOOR STATIONS SERIES DS3/DS3B

BD3/D3/BD3B/D3B

At each door station location, strip approximately 4 Inches of

jacket from wire and

separate colored

conductors from one

another. Strip 1/2 Inch of

insulation from each

conductor as shown in

figure 9. Cut each shield

drain wire at jacket to

prevent them from

touching each other

(MS4DCXSC only).

Terminate yellow and

orange wires to the

screw terminals on the

bell button (if equipped).

Connect the Red and

Black wires to the Red

and Black wires on the

speaker respectively.

Refer to figure 10. Mount

door station to housing

using the two screws

provided with station.

1 2

Podsumowanie treści

Strona 1 - MPORTANT: THE USE OF NON

CONGRATULATIONS!Your purchase of an M&S music and communications system is an investment that will provide years of enjoyment and service foryour

Strona 2 - MONITOR OVERRIDE FEATURE

Figure 12Figure 13Figure 14Figure 15AM ANTENNAFM DIPOLE ANT(ORANGE)TM2 TUNER MODULEAM FM ANTENNAFigure 16Figure 17Figure 11Gather all remote anddoor s

Komentarze do niniejszej Instrukcji

Brak uwag

M&S Systems MC602 Instrukcja Użytkownika

Przeglądaj online lub pobierz Instrukcja Użytkownika dla Budziki M&S Systems MC602. 115755D Instrukcja obsługi

Podsumowanie treści

Komentarze do niniejszej Instrukcji